18NDS100U1 Subwoofers 18 inchs
 
            Notes
- 4 INCH COPPER VOICE COIL
 
- 97.7 dB/SPL SENSITIVITY
 
- 2000 WATT PROGRAM POWER HANDING
 
- FEM OPTIMIZED MOTOR AND SUSPENSIONS
 
- OPTIMIZED COOLING SYSTEM
 
- DOUBLE SPIDER
 
- RESONANCE FREE AND HEAVY DUTY BASKET DESIGN
 
- ALUMINIUM DEMODULATING RING
 
- TRIPLE ROLL SURROUND
          - 97.7 dB/SPL SENSITIVITY
- 2000 WATT PROGRAM POWER HANDING
- FEM OPTIMIZED MOTOR AND SUSPENSIONS
- OPTIMIZED COOLING SYSTEM
- DOUBLE SPIDER
- RESONANCE FREE AND HEAVY DUTY BASKET DESIGN
- ALUMINIUM DEMODULATING RING
- TRIPLE ROLL SURROUND
GENERAL SPECIFICATIONS
| Nominal diameter | 461(18) mm (in.) | 
|---|---|
| Nominal impedance | 8 Ω | 
| Minimum impedance | 6.6 Ω | 
| Program power (1) | 2000 W | 
| AES Power rating(2) | 1000 W | 
| Sensitivity (3) | 97.7 dB | 
| Frequency range | 40 ~ 1000 Hz | 
| Voice coil diameter | 100(4) mm (in.) | 
| Chassis material | Aluminium | 
| Magnet material | Neodymium | 
| Magnet dimensions (ODxIDxh) | 97 x 25 x 10 mm | 
| Coil material | SV | 
| Former material | Glass Fiber | 
| Xmax(4) | 10.5 mm | 
| Xmech(5) | 16 mm | 
| Gap height | 10 mm | 
| Voice coil Winding height | 26 mm | 
SMALL SIGNAL PARAMETERS
| DC resistance(Re) | 5.5 Ω | 
|---|---|
| Resonance frequency(Fs) | 40 Hz | 
| Moving mass(Mms) | 243 g | 
| Compliance(Cms) | 0.08 mm/N | 
| Force factor(BL) | 26.90 N/A | 
| Mechanical Q-factor(Qms) | 10.4 | 
| Electrical Q-factor(Qes) | 0.45 | 
| Total Q-factor(Qts) | 0.43 | 
| Equivalent air volume(Vas) | 145 I | 
| Voice coil Inductance(Le) | 1.80 mH | 
| Diaphragm area(Sd) | 1325 cm2 | 
| Reference efficiency(Eta O) | 2.3 % | 
SHIPPING INFORMATION
| Net weight | 10.6 Kg | 
|---|---|
| Multipack size (1) (W x D x H) | 485 x 485 x 245 mm | 
| Multipack weight | 12.6 Kg | 
OTHERS
(1)Program power is defined as 3 dB greater than AES Power.
(2) Tested for two hours using a continuous, band-limited pink noise signal as per AES 2-1984 Rev. 2003. Loudspeaker tested in free air.
(3) From T/S parameters, measured with LMS DA LPM module.
(4) The Xmax is calculated as: (Hvc - Hg)/2+ Hg/4. Hvc is the voice coil height and Hg the gap height.
(5) The Xmech is calculated as: (Hvc - Hg)/2 +(Hg-2). Hvc is the voice coil height and Hg the gap height.
(6) Thiele-Small parameters are measured after preconditioning: a) at 20°C- 22°C, 50% humidity for 2 hours; b) by LMS LSI measurement.
          (2) Tested for two hours using a continuous, band-limited pink noise signal as per AES 2-1984 Rev. 2003. Loudspeaker tested in free air.
(3) From T/S parameters, measured with LMS DA LPM module.
(4) The Xmax is calculated as: (Hvc - Hg)/2+ Hg/4. Hvc is the voice coil height and Hg the gap height.
(5) The Xmech is calculated as: (Hvc - Hg)/2 +(Hg-2). Hvc is the voice coil height and Hg the gap height.
(6) Thiele-Small parameters are measured after preconditioning: a) at 20°C- 22°C, 50% humidity for 2 hours; b) by LMS LSI measurement.

 
                  
                  
                 
                  
                  
                 
            