24NDS151U1 Subwoofers 24 inchs
Notes
- 6 INCH COPPER VOICE COIL
- 97.2 dB/SPL SENSITIVITY
- 5000 WATT PROGRAM POWER HANDING
- FEM OPTIMIZED MOTOR AND SUSPENSIONS
- 57mm PEAK TO PEAK MAXIMUM EXCURSION
- OPTIMIZED COOLING SYSTEM
- DOUBLE SPIDER
- RESONANCE FREE AND HEAVY DUTY BASKET DESIGN
- TRIPLE ROLL SURROUND
- 97.2 dB/SPL SENSITIVITY
- 5000 WATT PROGRAM POWER HANDING
- FEM OPTIMIZED MOTOR AND SUSPENSIONS
- 57mm PEAK TO PEAK MAXIMUM EXCURSION
- OPTIMIZED COOLING SYSTEM
- DOUBLE SPIDER
- RESONANCE FREE AND HEAVY DUTY BASKET DESIGN
- TRIPLE ROLL SURROUND
GENERAL SPECIFICATIONS
| Nominal diameter | 620(24) mm (in.) |
|---|---|
| Nominal impedance | 4 Ω |
| Minimum impedance | 4.8 Ω |
| Program power (1) | 5000 W |
| AES Power rating(2) | 2500 W |
| Sensitivity (3) | 97.2 dB |
| Frequency range | 28~1000 Hz |
| Voice coil diameter | 151(6) mm (in.) |
| Chassis material | Aluminium |
| Magnet material | Neodymium |
| Magnet dimensions (ODxIDxh) | 146x60x10 mm |
| Coil material | SV |
| Former material | Glass Fiber |
| Xmax(4) | 17.75 mm |
| Xmech(5) | 28.5 mm |
| Gap height | 17 mm |
| Voice coil Winding height | 44 mm |
SMALL SIGNAL PARAMETERS
| DC resistance(Re) | 3.6 Ω |
|---|---|
| Resonance frequency(Fs) | 28.2 Hz |
| Moving mass(Mms) | 523 g |
| Compliance(Cms) | 0.06 mm/N |
| Force factor(BL) | 29.8 N/A |
| Mechanical Q-factor(Qms) | 5.67 |
| Electrical Q-factor(Qes) | 0.39 |
| Total Q-factor(Qts) | 0.37 |
| Equivalent air volume(Vas) | 486 I |
| Voice coil Inductance(Le) | 2.09 mH |
| Diaphragm area(Sd) | 2376 cm2 |
| Reference efficiency(Eta O) | 2.6 % |
SHIPPING INFORMATION
| Net weight | 25.7 Kg |
|---|---|
| Multipack size (1) (W x D x H) | 635X635X318 mm |
| Multipack weight | 28.8 Kg |
OTHERS
(1)Program power is defined as 3 dB greater than AES Power.
(2) Tested for two hours using a continuous, band-limited pink noise signal as per AES 2-1984 Rev. 2003. Loudspeaker tested in free air.
(3) From T/S parameters, measured with LMS DA LPM module.
(4) The Xmax is calculated as: (Hvc - Hg)/2+ Hg/4. Hvc is the voice coil height and Hg the gap height.
(5) The Xmech is calculated as: (Hvc - Hg)/2 +(Hg-2). Hvc is the voice coil height and Hg the gap height.
(6) Thiele-Small parameters are measured after preconditioning: a) at 20°C- 22°C, 50% humidity for 2 hours; b) by LMS LSI measurement.
(2) Tested for two hours using a continuous, band-limited pink noise signal as per AES 2-1984 Rev. 2003. Loudspeaker tested in free air.
(3) From T/S parameters, measured with LMS DA LPM module.
(4) The Xmax is calculated as: (Hvc - Hg)/2+ Hg/4. Hvc is the voice coil height and Hg the gap height.
(5) The Xmech is calculated as: (Hvc - Hg)/2 +(Hg-2). Hvc is the voice coil height and Hg the gap height.
(6) Thiele-Small parameters are measured after preconditioning: a) at 20°C- 22°C, 50% humidity for 2 hours; b) by LMS LSI measurement.
